熊好夾選物販賣

Although we use the term "clip doll", But in fact, the prizes placed in the machine are no longer limited to dolls. At present, the most common ones are: "3C products", "puddings" and "boxed dolls"... and so on. When I first saw the doll machine and its operation panel, I naively thought that the doll machine was just Use the rocker to move the paw over the item, then press the button and it will take the item to the hole. This is wrong. If this is the case, then isn't it possible to pinch an item every ten yuan? But as far as I know, I have heard that some people around me still think so. The most basic setting of the doll machine is this: "Press the button and the claw will grab the item and release it to the highest point. The claw will move back above the hole." Basically all the machines are set up like this, so it's not easy to clip the items out. The claws of Taiwanese dolls are mainly three-claws, and the machines are also large and small. Each machine can make different settings. The settings vary according to the owner. Many settings cannot be seen from the appearance. Therefore, many times, it is necessary to "send ten questions" to test the Taiwanese. At present, there are three types of common doll machines: "Ordinary Terrace (most common)", "Groove Terrace (the entrance is a strip, not a corner)", "Bouncing Platform" Here is a brief explanation of what is called a bouncing platform. The most common prize in the bungee jumping platform is the "small waist speaker". The bottom of the table is a woven elastic rope. The hole is specially designed. After the player has clipped the clip, the item is clipped to the highest point and then falls, and the item that falls on the rope will bounce. The ultimate goal is to make the item into a specially designed hole, basically a "pure luck station." If you want to know more about it, you can find related videos by searching for relevant keywords on Youtube for reference. Second, the introduction of common nouns * Claw position: As mentioned above, the Taiwan machine is mainly three-claw, and the claw position is the relative position of the three-claw to the prey. Using the claw position is a very basic but important concept, usually by changing the claw position by continuously rotating the rocker. However, some machines lock the claws tightly and cannot easily change the claw position. *Twist: A setting that can be changed by the owner. When the claw is adjusted and the button is pressed, some machines will be in the lower jaw. Rotate the claws to destroy the original good claw position. *Paw force: The force that the claws hold the item can be adjusted by the owner. If the "Three-Prong All-Inclusive" still can't grab the item, It is highly recommended not to challenge the machine (or the prey, it may be too heavy for prey). * Claw cover: Located at the upper end of the claw, it can increase the friction and make the item more easily pinched. (not all paws have claws) * Guaranteed gripping: Usually, each machine will have a guaranteed amount of money. When the coin reaches the amount, no coin is required. And you can play infinitely until the prize is clipped. At this time, the setting of the claw will change, and the item will be directly put together after the item is clipped. Clip it to the hole before letting go. *Electric eye: Usually placed somewhere on the wall of the hole, it is a device used to judge whether the item has been successfully gripped. * Crane: The machine that moves the claws (see the picture below). If the crane moves too slowly, it will have the effect of blocking the claws. The blue circle at the picture is the crane: *Baffle: Under normal circumstances, the hole should be the same height as the bottom of the machine, but in order to increase the difficulty, many machines will be next to the hole. The board is surrounded by a board, which is called a "baffle." *Two collections: a technique commonly used for a pair of dolls. Press the button once after the lower jaw, the claws will close the claws. This is called "two collections". But not all machines can do this. *Belt: Commonly on the box, similar to the hair ring, tied to the box, and sometimes makes the item more easily pinched. But there is also a saying that it has the function of defending and turning over. * Second floor: The items are stacked on other items, and there are many baffles higher than other items. The position is called "second floor". * Gun position: The item is located at a position where it is easy to be pinched, called "gun position." * Shipment: The item is successfully clipped. * Hot claws: When the number of consecutive grips is too high, the temperature of the claws rises, and the claw force is weaker than normal. * Delayed lower jaw: Normally, when the button is pressed, the paw should immediately lower the paw, and the delayed paw is: "Put down the button and pause for a short time before you can lower your claws." *Claw: In the non-protective mode, after the item is caught by the claw, the claw will pinch the item over the hole to release. * Card hole: The item is clipped out and stuck in the hole, called the card hole. It is specially made to distinguish it from the "claw". * Anti-mite film: There is usually a piece of iron between the claw and the machine on it, called "anti-smashing film". The tighter the tamper-proof lock (closer to the paw), the more difficult it is to cause the paw to move. * In the red circle in the picture, the closer to the bottom, the tighter the paws* * Claws: Use the rocker to move the claws before the lower jaws, and grasp the timing of the lower jaws so that the claws rise diagonally when they rise. The claws personally feel that the difficulty is really high, especially the speed of the lower jaw of each machine is different, and it needs to be fine-tuned. The "anti-smashing film" and "delayed lower jaw" mentioned above are all adjustments to the claws. * Internal loss: After the item is clipped, the claw will throw the item inside (inverted from the hole), and some will lose the stage. It can be seen from the appearance that the anti-smashing piece is inclined and has a high probability of being lost inside. The solution to the internal loss is usually to squeeze the thin (the claw only catches a small part of the item). However, the difficulty of losing the platform itself is still high. *La: When the items in the table are placed at a higher height than the claws, you can push the items directly with your claws. This technique is called "La". There are also some terms like "reverse claws", "reverse push", "turning over", etc., which are some common techniques. There are a lot of videos on YouTube that introduce these techniques, and it’s much better to understand them in terms of videos than in words.